Defi-Link Display VSD CONCEPT is a product to display information on the speed, engine speed, and so on by reflecting the information on the windshield of vehicle. The projection technology is called “Heads Up Display(HUD).” VSD is our original technology focusing on compactness and universality utilizing the HUD technology.
By connecting this product to the Defi-Link System, oil temperature, water temperature, oil pressure, fuel pressure, and exhaust temperature can be displayed other than speed and engine speed.
The production of the Defi-Link Display VSD CONCEPT has been ended in April, 2007.
Two super high bright LED indicators
The switch panel is illuminated with LEDs to make operation in the dark easy.
The brightness is adjusted automatically. (A dim sensor is included in the product.)
Auto dimmer mode and manual dimmer mode are available. When the auto dimmer mode is selected, the brightness of display is adjusted automatically depending on the outside light.
The structure of the installation stay allows 2 way angle adjustments.
Displays speedometer and engine speed. By connecting to the Defi-Link System and sensors(sold separately) various information is displayed.
Functions listed below with “#” marks are available when the Defi-Link VSD Concept is connected to Defi-Link Control Unit II (or Defi-Link Control Unit) and sensors are connected.
Following information is displayed in Digital and bar display.
Unit: mm/inches
| Display contents | Digital display | Bar display |
|---|---|---|
| Speed | Available | N/A |
| Engine speed | N/A(Special Display) | Available |
| Oil pressure # | Available | Available |
| Fuel pressure # | Available | Available |
| Oil temperature # | Available | N/A |
| Water temperature # | Available | N/A |
| Exhaust temperature # | Available | N/A |
Data on turbo or boost cannot be displayed.
Warning values can be set discretionary. Double warning of engine speed is also settable by equipping two LED indicators.
Connected sensor data and speed data can be recorded for a maximum of 3 minutes. The data can be replayed later.
When a non-displayed value exceeds the set value, the display changes from selected data to the current warning value automatically.
Opening and ending modes are performed after the ignition key is turned on and off.
The brightness is adjusted automatically.
Auto dimmer mode and manual dimmer mode are available. When the auto dimmer mode is selected, the brightness of display is adjusted automatically depending on the outside light. The brightness can be selected from 3stages.
When the manual dimmer mode is selected, the brightness of display is fixed. The brightness can be selected from 5 stages.
When a state with a speed of 0km/h or 0MPH continues for more than 10 seconds, special display is played.
Oil temperature or water temperature is displayed until the temperature reaches the set value.
Signals of oil temperature or water temperature can be output when it reaches the set value. It’s possible to operate a warning lamp or a motor when a temperature reaches the set value.
Maximum values which sensors are connected are displayed. If speed is recorded, the minimum value can be displayed.
D.C.Unit(exclusive unit for Defi-Link Display VSD CONCEPT) has 3 LINK connectors for Defi-Link Meters.
Wiring example of Defi-Link VSD Concept and Defi-Link System.
Defi-Link Display VSD CONCEPT can operate independently.
When the Defi-Link VSD Concept is used WITHOUT the Defi-Link System.
| Speed/Engine speed | Peak display | Special display |
|---|---|---|
 |
 |
 |
When the Defi-Link VSD Concept is connected to the Defi-Link System.
| Water temperature # / Engine speed | Oil temperature # / Engine speed | Oil pressure # / Engine speed |
|---|---|---|
 |
 |
 |
| Exhaust temperature # / Engine speed | Fuel pressure # / Engine speed | Speed/Oil pressure # |
|---|---|---|
 |
 |
 |
| Speed/Fuel pressure # | Auto warning | Tacho warning |
|---|---|---|
 |
 |
 |
| ① | SELECT/▽DOWN SWITCH |
|---|---|
| ② | BAR SELECT/▲UP SWITCH |
| ③ | ENTER/DIM/SET UP SWITCH |
| ④ | PEAK/RESET SWITCH |
| ⑤ | For Display unit |
| ⑥ | For Speed & Tacho signal wire(White) |
| ⑦ | For Power supply wire / Power supply link wire(White) |
| ⑧ | For Power supply wire / Power supply link wire(White) |
| ⑨ | For Control Unit Ⅱ / Control Unit / Gauge / Display(White) |
| ⑩ | For Control Unit Ⅱ / Control Unit / Gauge / Display(White) |
| ⑪ | For Control Unit Ⅱ / Control Unit / Gauge / Display(White) |
| ⑫ | For Control output(Red) |
| ⑬ | Unuset(Black) |
| ⑭ | DIM Sensor(Black) |
*Groove
Wires ⑩ through ⑬ can be fit in the place neatly.
| Power supply voltage | DC10 to 15V(Exclusive for 12V vehicle) |
|---|---|
| Current consumption | +B line MAX 1A only while the closing mode is displayed. (Dark current 0mA) IGN MAX 1A ILM MAX 0.1A |
| Display Range SI | Speedometer（SP）0～400km/h（0～240MPH） |
| Tachometer(TA)0～9,500rpm | |
| Oil temperature（O.TEMP.）50～150℃（122～302°F） | |
| Water temperature（W. TEMP.）20～120℃（68～248°F） | |
| Oil pressure（OIL. P.）0～1,000kPa（0～145PSI） | |
| Fuel pressure（FUEL. P.） 0～600kPa（0～87PSI） | |
| Exhaust temperature（EXT. T.）200～1,100℃（390～2,010°F） | |
| Applicable speed pulse | A) 2, 4, 8, 16(mainly for Japanese vehicles) B) Free pulse setting: 2,051 pulse/mile to 26,665 pulse/mile, 1,274 pulse/km to 16,562 pulse/km |
| Applicable Number of Cylinders | Without 1, 2, 3, 4, 5, 6, 8 (Set up with D.C.Unit.) If connected to the Defi-Link Control Unit Ⅱ Version 2.0(DF05002):1, 2, 3, 4, 5, 6, 8* If connected to the Defi-Link Control Unit Ⅱ(DF05001): 3, 4, 5, 6, 8* If connected to the Defi-Link Control Unit(DF01301): 3, 4, 5, 6, 8* *Set up with each control unit. |
| NOTE |
*This product is for only on vehicles with a 12V electrical system. Never use this product on 24V vehicles. *Engine speed can not be displayed when installed in diesel vehicles. *Engine speed can not be displayed when installed in vehicles without a engine revolution signal. *This product can not be installed in vehicles without a speed signal. *This product can not be installed in altered vehicles. *When sensors are installed additionally, proper sensor attachments are necessary to be purchased. |
The following parts are included with this product. Confirm that all parts are present before installing the product. In addition, these parts are sold separately for part replacement. Contact your retailer for further information.
NOTE: A Japanese operation manual, a wiring manual, and a questionnaire card are included other than the parts listed below. They are effective only in Japan.
| Display unit (wire 8 1/3ft, 2.5m) | 1 |
| D.C.Unit (Exclusive Control Unit) | 1 |
| Speed & Tacho Signal Wire (green/speed, blue/tacho) 6 2/3ft, 2m |
1 |
| Tachometer Signal Wire (Blue) | 1 |
| DIM Sensor (wire 6in, 0.15m) | 1 |
| Power Supply Wire 2 1/2ft, 0.75m | 1 |
| Meter Wire 10in, 0.25m *Use only when connected to the Defi-Link System. |
1 |
| Power Supply Link Wire 10in, 0.25m *Use only when connected to the Defi-Link System. |
1 |
| Control Out Wire (pink) 3 1/3, 1m *Use only when connected to the Defi-Link System. |
1 |
| Operation manual | 1 |
| Terms and Conditions | 1 |
| Double-sided tape | 2 |
| M4 Bolt, Nut, Washer | 1each |
| Tapping Screw(for Mounting Bracket) | 2 |
| Mounting Bracket | 1 |
| Clamp | 4 |
| Solderless connector | 6 |
No part is necessary to be purchased.
[CASE1] Defi-Link Control Unit Ⅱ (or Defi-Link Control Unit) is already connected.
No part is necessary to be purchased.
If you want the data which sensors are not connected, the sensor sets(sensor and sensor wire) needs to be purchased. Sensor sets are sold as optional parts. Sensor sets for oil pressure, fuel pressure, oil temperature, water temperature, and exhaust temperature are available.
[CASE2] Defi-Link Control Unit Ⅱ (or Defi-Link Control Unit) is not connected yet.
Defi-Link Control Unit Ⅱ and sensor sets needs to be purchased.
When sensors are installed, the following commercial parts are necessary to be purchased:
| Sensor | Necessary commercial parts | sensor thread size |
|---|---|---|
| Oil pressure | Sensor attachment Teflon tape |
1/8PT |
| Fuel pressure | Three-way joint hose union Teflon tape |
1/8PT |
| Oil temperature | Sensor attachment Teflon tape |
1/8PT |
| Water temperature | 2 Clamps Sensor attachment Teflon tape |
1/8PT |
| Exhaust temperature | Nothing | 1/8PT |
| Item | Model Number |
|---|---|
| Defi-Link Control Unit Ⅱ Version2.0 | DF05002 |
| Oil Pressure Sensor Set | PDF00713SS |
| Fuel Pressure Sensor Set | PDF00806SS |
| Oil Temperature Sensor Set | PDF00908SS |
| Water Temperature Sensor Set | PDF01006SS |
| Exhaust Temperature Sensor Set | PDF01114SS |
| Oil/Water Temp. Sensor | PDF00903S |
Sensor thread sizes are all 1/8PT.
| Item | Model Number |
|---|---|
| Fuse for Power Supply Wire(4A) | PDF05005G |
| Rubber for Target Screen | PDF05711G |
| Mounting Bracket set | PDF05712G |
