BF Tachometer is a standalone tachometer which consists of a gauge, a switch unit, and a big warning indicator. BF Tachometer is not necessary to be connected to a control unit.
BF Tachometer is an electronic blacked out gauge which is high response and refined design. When the car is off they have a black face with no numbers on them. As soon as the car is turned on, the gauges light up and are in full affect.
The diameter is 80mm (3 1/8″). The scale variety is 9000RPM and 11000RPM. The color variety is white, amber red, and blue.
Blue Models are not available in USA. (White and Amber Red Models are available in USA.)
BF Tachometer cannot be linked with the Defi-Link System
The production of the BF Tachometer has been ended in April, 2010.
Maximum angle of deflective 270 degrees (full sweep) is controlled by the microcomputer up to 4600 division (0.057degrees each) to provide high precision in the accuracy of information generated. The stepping motor is sufficient for quick response of all sorts of professional motorsports.
*Wide-angle scale is used at the idling range 0~3,000RPM.
*The scale is fitted to recent engine power band and linear scale is used from 3,000RPM to 11,000RPM.
The gauge dial is invisible while the ignition switch is off. Once the ignition switch is turned on, a clear display appears by colored LED illumination. The gauge dial illumination and the red emitting needle pointer provide high visibility
The gauge dial and the needle pointer performs opening and closing modes interlocked with turning ON/OFF of the ignition.
The maximum RPM during driving can be stored and checked later.
There are 5 stages of brightness for the daytime and 6 stages for the nighttime. The brightness can be decreased/increased with the vehicle lights switched on/off.
Two customer-defined warning RPMs can be set. When the RPMs are exceeded, the warning LED blinks/lights up and the warning buzzer sounds.
The exclusive large-sized indicator which lights in green and red enhances the visibility of warnings in addition to the warning LED in the gauge.
The large-sized switch unit with light is fixable on the gauge and is also detachable.
The gauge is clinched by using the exclusive mounting band and back case. Wires can be stored in the back case neatly.
Gauge dials are invisible while the ignition switch is off. Once the ignition switch is turned on, a clear display appears with white LED illumination. A red emitting needle pointer increases visibility.
Ignition off
Ignition on(Amber Red Model)
| Power supply voltage | DC10 to 15V(Exclusive for 12V vehicle) |
|---|---|
| Current consumption | +B(Ignition on) Maximum(six gauges) 2.5A |
| Applicable Number of Cylinders | 1, 2, 3, 4, 5, 6, 8 |
| Applicable Engine speed Pulse |
Engine speed input(bllue) [V1] 4.0V and above [V2] 0 to 1.5V (Graph1)  |
| Display Range | 0~9000RPM, 0~11000RPM |
| NOTE |
*Products is for only on vehicles with a 12V electrical system. Never use products on 24V vehicles. *Products can not be installed in altered vehicles. |
The dial diameter is 80mm(3 1/8in).
White Model, Amber Red Models, and Blue Model are available. The switch illumination color is the same as the color of gauge illumination.
*Blue Models are not available in USA.
Pictures may differ from the real products by processes and photography conditions, etc.
| Part Name | Quantity |
|---|---|
| Gauge | 1 |
| Switch unit (wire 45cm, 1.48ft) | 1 |
| Regular Position Bezel | 1 |
| Back case | 1 |
| Mounting band | 1 |
| Mounting rubber | 1 |
| Power supply & tachometer signal wire 2.2m, 7.2ft | 1 |
| Indicator (wire 20cm, 7.8in) | 1 |
| Operation manual | 1 |
| Terms and Conditions | 1 |
| Mounting bracket | 1 |
| Attachment for switch unit | 1 |
| M6 bolt | 2 |
| Spring lock washer | 2 |
| Washer | 2 |
| Spacer | 1 |
| Buffer | 1 |
| Double sided tape | 1 |
| Tapping screw | 2 |
| Solderless connector | 5 |
| Repair parts | Model Number |
| 80mm (3 1/8″) Back case set (Back case x 1, Buffer x 1) |
PDF07101G |
| Power supply & tachometer signal wire | PDF07102H |
| 80mm (3 1/8″) Mounting band set (Mounting band x 1, Mounting rubber x 1) |
PDF07103G |
| 80mm (3 1/8″) Mounting bracket set (Mounting bracket x 1, M6 bolt x 2, Spring lock washer x 2, Washer x 2, Spacer x 1, Tapping screw x 2) |
|
| 80mm (3 1/8″) Regular Position Bezel | PDF07105G |
| Fuse for Power supply wire(1A) 2pcs | PDF07113G |
