Mode Setting
Before using the product, you will need to set the product modes to
correspond to the specifications of your vehicle.
If the product settings are not correct, the product will fail to
operate.
|
SPEEDOMETER AND TACHOMETER SETTINGS
To modify the factory settings of the following items, press the
SET switch and hold it for more than 2 seconds while in the normal
mode. The speed mode will then be activated.
|
|
ITEM
|
DISPLAY
|
SETTING RANGE
|
UNIT OF DISPLAY
|
FACTORY SETTING
|
| 1)Speedometer Pulse Type |
P-4
|
2, 4, 8, 16(Pulse)
|
-
|
4(Pulse)
|
| 2)No. of Cylinders |
E - 4
|
3, 4, 5, 6, 8 (Cylinders)
|
-
|
4(Cylinders)
|
| 3)Speedometer Units |
Km/h
|
MPH, km/h
|
MPH, km/h
|
Km/h
|
| 4)LED Display |
LED
|
LED ON, OFF
|
-
|
LED(ON)
|
| 5)Special Display |
SPEC
|
Special Display ON, OFF
|
-
|
LED(ON)
|
6)LED Speedometer
Step Value |
S - 20
|
10, 20(MPH)
10,20,30,40(km/h)
|
MPH or km/h
|
20(km/h)
|
7)LED Tachometer
Step Value
|
1000
|
200 to 1000(r/min)
(in units of 200)
|
r/min
|
1000(r/min)
|
8)LED MAX.
Tachometer Value |
7000
|
1000 to 9900(r/min)
(in units of 100)
|
r/min MAX
|
7000(r/min)
|
|
NOTE: The mode changes each time the SET switch is pressed less
than 2 seconds.
|
1)Speedometer Pulse Type
|
|
2)No. of Cylinders
|
|
|
|
|
|
8)LED Tachometer
MAX.Value
|
|
3)Speedometer Units
|
|
|
|
|
|
7)LED Tachometer
Step Value
|
|
4)LED Display
|
|
|
|
|
|
6)LED Speedometer
Step Value
|
|
5)Special Display
|
|
|
|
|
1)Setting Speedometer Pulse Type
Set the number of pulses using the Up and DOWN switch.
< Speedometer Pulse Type >
Speedometer pulse type varies with the model of the vehicle and normally
the number of pulses of the vehicle is 4 pulse. Most Nissan vehicles
have 2 pulse speedometers although the Nissan Y32 Cedric, Gloria and
Cima have 16 pulse speedometers.
Please ask your local dealer if you are not sure of the speedometer
pulse type of your vehicle.
|
|
2) Setting the Number of Cylinders
Press the SET switch once, and use the UP and DOWN switch to set the
number of cylinders.
|
|
3) Setting the Speedometer units of measure
Press the SET switch once, and use the UP and DOWN switch to set the
desired units of measure.
|
|
4) Setting the LED Display
Press the SET switch once, and use the UP and DOWN switch to set the
LED Display ON or OFF.
|
|
5) Setting the Special Display
Press the SET switch once, and use the UP and DOWN switch to set the
Special Display ON or OFF.
|
|
6) Setting the LED Speedometer Step Value
Press the SET switch once, and use the UP and DOWN switch to set the
Speedometer Step Value.
|
|
7) Setting the LED Tachometer Step Value
Press the SET switch once, and use the UP and DOWN switch to set the
LED Tachometer Step Value.
|
|
8) Setting the LED Tachometer Maximum Value
Press the SET switch once, and use the UP and DOWN switch to set the
Tachometer Max.Value.
|
|
If the SET switch is pressed once, the system will return to SPEEDOMETER
units setting. In any set mode, the system will return to NORMAL MODE.
If the SET switch is pressed for more than 2 seconds.
If the engine revolutions exceed the set Tachometer MAX. Value, all
the LED lamps will flash. If the engine revolutions drop below the
set Tachometer MAX. Value, the LED lamps will go out gradually, counting
backward to the set Tachometer MAX. Value.
<EXAMPLE> If the Tachometer MAX Value is set to 7400 r/min and
Tachometer Step Value is set to 400 r/min, the LED lamps will appear
as indicated below at the specified engine revolution rates noted.
|
 :
LED ON |
 :
LED OFF |
|
| Revolutions(r/min) |
LED State |
Revolutions(r/min) |
LED State |
| 0 to 4900 |
|
6200 to 6500 |
  |
| 5000 to 5300 |
|
6600 to 6900 |
|
| 5400 to 5700 |
|
7000 to 7300 |
|
| 5800 to 6100 |
|
7400 to 9900 |
|
|
Please note that Section 25269 of the California Vehicle Code
provides that " no person shall display a steady burning
red warning light on a vehicle," except as may otherwise
be provided herein. The exceptions permitting red lights apply
to emergency vehicles and other situations that are not be applicable
to the V.S.D. instruments. Other states have similar prohibitions
in their respective vehicle codes.
Note that the V.S.D. display unit projects light upwards upon
the transparent screen, so that the image can be reflected into
the driver's line of sight. In some situations, it is possible
that the light from the LEDs of the display unit may be visible
to a person located in front of the vehicle, either because
the angle at which the display unit is mounted on the dashboard
or because the angle of the dashboard is inclined towards the
front of the vehicle.
If this is the case, the applicable regulatory authorities might
interpret the use of the V.S.D. display unit to be a violation
of California Vehicle Code Section 25269 or other state vehicle
codes. |
|
End
of Life Products |
