Before using the product, you will need to set the product modes to
correspond to the specifications of your vehicle. If not, the product
will fail to operate. If you disconnect the battery, you will need
to set the product modes again.
|
|
SETTING MODE
|
SPEEDOMETER AND TACHOMETER SETTINGS
Select the Speedometer/Tachometer mode using the 
switch. Press the 
switch and hold it for more than 2 seconds. The initial setting mode
will then be activated. |
|
ITEM
|
DISPLAY
|
SETTING RANGE
|
UNIT OF DISPLAY
|
FACTORY SETTING
|
| 1)Speedometer Pulse Type |
|
2, 4, 8, 16(Pulse)
|
-
|
4(Pulse)
|
| 2)No. of Cylinders |
|
3, 4, 5, 6, 8 (Cylinders)
|
-
|
4(Cylinders)
|
| 3)Speed Warning |
|
0 to 400
(10km/h increments)
|
km/h
|
100(km/h)
|
4)Revolution Warning
|
|
400 to 9900(rpm)
(100rpm increments)
|
-
|
3000(rpm)
|
| 5)Speed Governor Release |
|
130, 180(km/h)
|
km/h
|
180(km/h)
|
Above different modes can be selected by pressing the
switch. Then, the preset values can be changed by pressing the 
 switch. If you
press the switch
again and hold it for more than 2 seconds, the unit returns to normal
mode.
< Speedometer Pulse Type >
Speedometer pulse type varies with the model of the vehicle and normally
the number of pulses of the vehicle is 4 pulse. Most Nissan vehicles
have 2 pulse speedometers although the Nissan Y32 Cedric, Gloria and
Cima have 16 pulse speedometers.
Please ask your local dealer if you are not sure of the speedometer
pulse type of your vehicle.
|
TIME
SETTING
1. Press the switch
to select the clock mode and select it.
2. Press and hold the
switch for more than 2 seconds and "Hour" increment will
blink. Then, press the
switch to adjust
the "Hour."
3. Press the switch
again and "Minute" increment will blink. Press the
switch to adjust
the "Minute".
4. Press and hold the
switch for more than 2 seconds again to exit the time setting mode.
|
|
|
NORMAL MODE
|
Modes changes each time the switch is pressed.
|
|
SPEEDOMETER/TACHOMETER(SP-TA)
MODE
The speed value is displayed digitally while the value of tachometer
is displayed on the FLT (Fluorescent Tubing) bar.
If the speed warning value is exceeded; Yellow LED lights. If the
tachometer warning value is exceeded; Red LED lights.
|
 |
|
DRAG RACE(ZERO FOUR) MODE
*If the switch
is pressed at the initial value, "0.00", the countdown will
start before
3 seconds.
*When the countdown reaches "0.00" on the display, time
measurement will begin.
*When the time measurement interval has elapsed, driving time and
highest recorded speed are displayed in sequence.
*If the switch is pressed again, time measurement will begin.
*The FLT (Fluorescent Tubing) bar on the display turns off by 100
meters.
*If the vehicle begin to move before the countdown reaches "0.00",
a premature buzzer sounds and
no measurement occurs. |
|
< How to confirm your best time records. >
The best three of driving times are stored and updated in memory of
the unit.
*Each time the
switch is pressed,
the best three driving times are displayed .
If the switch is
pressed, the value is reset to the initial value, "0.00".
* The best three driving times can be cleared if the
switch is pressed and held for more than 2 seconds. |
|
CLOCK
MODE
The current time is displayed. (Please refer to Time Setting described
above.)
The FLT (Fluorescent Tubing) bar displays the value of the tachometer.
|
|
|
|
ELAPSED
TIME(HOUR METER) MODE
*If the switch
is pressed at the initial value, "0.00", the colon on the
display will blink
and the time elapsed since the engine of your vehicle is started will
be calculated.
*If the switch
is pressed again, the calculation will stop and restart.
*If the switch
is pressed and held for more than 2 seconds, the value on the display
will be reset to "0.00" (the colon lights on ).
The FLT (Fluorescent Tubing) bar displays the tachometer value. |
|
|
TRIP
MILEAGE AND TRIP COUNTDOWN MILEAGE MODES
Each time the switch
is pressed, Trip Mileage Mode and Trip Countdown Mileage Mode displays
in sequence.
|
< Trip Mileage Mode >
Trip mileage is displayed in 0.1 km increments.
*If the mileage displayed exceeds more than 999.99 km, mileage is
then displayed in 1 km increments from 1000 km.
*If the mileage displayed exceeds more than 9999 km, the value of
the mileage reverts to be added every 0.1 km increments from 0.0 km.
* If the switch
is pressed and held for more than 2 seconds, the trip mileage will
be reset to "0.00".
< Trip Countdown Mileage Mode >
*If the switch
is pressed and held for more than 2 seconds, the countdown mark on
the display will start to blink.
*Press the
switch to set the distance of the countdown mileage in 10 km increments.
*If the UP/DOWN switch is pressed continuously, the countdown mileage
changes in 100 km increments. |
|
|
If the countdown mileage is more than 1000 km, each time the
switch is pressed, the setting distance changes every 100 km.
*The countdown mileage can be set every 1000 km if the UP/DOWN
switch is pressed continuously.
*If the SET/CLR switch is pressed once, the instrument will exit
from the setting mode.
When the countdown mileage reaches "0.0 km" in TRIP
1 mode, the internal frame on the display light, the countdown mark
blinks and a buzzer sounds three times to indicate the end of the
countdown.
*In TRIP 2, the light of the internal frame on the display goes
off.
*The countdown mark blinks and a buzzer sounds five times to indicate
the end of the mileage countdown.
(Applicable to all MODES other than 0 to 400 Mode)
|
|
Please note that Section 25269 of the California Vehicle Code
provides that " no person shall display a steady burning
red warning light on a vehicle," except as may otherwise
be provided herein. The exceptions permitting red lights apply
to emergency vehicles and other situations that are not be applicable
to the V.S.D. instruments. Other states have similar prohibitions
in their respective vehicle codes.
Note that the V.S.D. display unit projects light upwards upon
the transparent screen, so that the image can be reflected into
the driver's line of sight. In some situations, it is possible
that the light from the LEDs of the display unit may be visible
to a person located in front of the vehicle, either because
the angle at which the display unit is mounted on the dashboard
or because the angle of the dashboard is inclined towards the
front of the vehicle.
If this is the case, the applicable regulatory authorities might
interpret the use of the V.S.D. display unit to be a violation
of California Vehicle Code Section 25269 or other state vehicle
codes. |
|
End
of Life Products |
