Defi Homepage
Home Club Defi Products Lineup Parts List Catalog Japanese Site
Contact Information Shops List Overseas Distributors
PRODUCTS
Defi-Link VSD X Defi-Link Meter BF Defi-Link Display Defi-Link Control Unit II  
Racer Gauge BF Tachometer Meter Hood & Option DIN-Gauge  
 
End of Life Products | Defi-Link Meter | VSD BASIS | VSD CONCEPT |
View of the engine control unit (ECU) for connections


How to attach the solderless connector



How to attach the display film
1. Before attaching the display film, clean the inside of the windshield.
2. To separate the film from the backing paper, attach adhesive tape to film and the backing paper about 2cm(4/5 in.) from the edge of the film and use the adhesive tape to pull the display film from its backing.
3.

Spray a mixture of water and mild detergent(1 to 2 the drops) on the windshield and on the side of the film to be applied to the windshield.

Apply the film to the windshield. Gently squeeze out excess any water or air bubbles from under the film and gently wipe any extra water away with a tissue or soft cloth. Do not scratch the film with the tissue or cloth.

How to set up the display unit and its stand
1. Gently slide the display unit onto the stand.
2. Adjust the position of the display unit so that it can be seen within a 5 inches of the bottom of the windshield. Gently tighten the screw on the stand after the display is positioned correctly.
 

NOTE:
Cover the display unit with a white cloth in high temperature conditions to prevent deterioration or damage to the components of the product.
Prior to using adhesive tape to attach the stand to the vehicle dashboard, please make sure that the dashboard area is free of oil, dust and water.
Wiring and Installation Procedure
Make sure that the product is compatible with your vehicle type.
1. Remove the vehicle ignition key and disconnect the negative ( - ) battery terminal.
2. Set number of cylinders in your engine using the cylinder switch on the control unit.
3. Locate the Vehicle ECU (refer to section on compatible vehicles.)
4. Connect the signal cable leads to the ECU (refer to section on ECU connections).

Use the solderless connectors to connect the signal cable to the ECU leads without cutting the wires connected to the ECU. Do not touch the battery terminals directly.
Depending on the vehicle model, if the length of the signal cable supplied is insufficient, then you will need to obtain additional wire of the same quality and gauge.
5. Before reconnecting the battery, make sure that all connections are correct and tight.
6. Connect the display unit cable to the control unit. (Make sure that the connector is correctly aligned).
7. Reconnect the negative(-) terminal on the battery.
8. Start the engine.
9. Confirm that the product is performing correctly according to the operating manual.
10. Cut a portion of the double sided adhesive tape provided with the product and attach it to the stand. The remainder will be used to attach the control unit in place.
11. Use the double-sided adhesive tape to attach the stand and the display unit in a convenient location.
12. Switch off the vehicle ignition, disconnect signal and display unit cables from control unit.

13.

 Attach the control unit in suitable location with the double sided adhesive tape.
14. Attach signal and display unit cables to the control unit. Make sure to align the connectors correctly.
15. Attach the display film in a location that allows the image of the display to be reflected into the driver's line of sight.
 
16. Test drive the vehicle to ensure display corresponds to vehicle's original equipment manufacturer instruments.

NOTE : Readings on the display may differ slightly from the vehicle's original equipment manufacturer instrument, however slight variations are normal because of different calibrations of the OEM instruments, variations in tire size and other factors.
In order to separate the display film from its backing, attach adhesive tape on both sides of the display film about 2cm ( 4/5 in.) from the edge of the film and pull the display film from its backing.

Spray a solution of water and a mild detergent (1 or 2 drops) on the windshield and on the display film.

Apply the film to the windshield while gently squeezing out any excess water and air bubbles with a tissue or soft cloth. Then use a tissue or soft cloth to remove any excess water from the windshield and display film.
Make sure that both the display unit and the control unit are firmly attached.
Make sure that the display can be viewed on a portion of the lower 5 in. of the windshield.
Attach the display unit in a location which will not hinder driving.
The company is not responsible for any damage to the vehicle arising from the use on application of the display film on windshield.

Please note that the laws of certain states prohibit applications of materials to a vehicle windshield other than in certain locations. For example, California Vehicle Code Section 26708(b) limits application of stickers or other materials to a 5-inch square area in the lower corner of the windshield nearest the driver.

On certain vehicle models, installation of the transparent film in such a location may be impractical, because limited clearance between the dashboard and the windshield may preclude attachment of the display unit to the dashboard at a position that will enable the driver effectively to view the reflection of the instrument display on the transparent film.

Please consult the laws of the jurisdiction in which you intend to operate your vehicle to determine whether similar laws or regulations would apply to you and if so, please examine the relative configuration of you dashboard and windshield to determine whether installation of the display unit as described in the installation manual will conform to requirements of local law.

Nippon Seiki Co.,Ltd., does not encourage installation of the products in violation of local laws or regulations and shall not be responsible for failure to obey local laws or regulations.