| Warning Setup Mode |
This screen allows setting of warnings for meters connected to
Defi-Link Control Unit II or Defi-Link Control Unit.
|
|
Item
|
Setting Range
|
Display Units
|
| 1 |
Turbo Meter |
-100 to 200kPa or -14.5 to 29.0PSI |
kPa or PSI |
| 2 |
Exhaust Temp. Meter |
200 to 1100oC or 390 to 2010oF |
oC or oF |
| 3 |
Oil Press. Meter |
0 to 1000kPa or 0 to 145PSI |
kPa or PSI |
| 4 |
Fuel Press. Meter |
0 to 600kPa or 0 to 87PSI |
kPa or PSI |
| 5 |
Oil Temp. Meter |
50 to 150oC or 122 to 302oF |
oC or oF |
| 6 |
Water Temp. Meter |
20 to 120oC or 68 to 248oF |
oC or oF |
| 7 |
Tachometer |
0 to 11000RPM |
RPM |
|
|
*Each time the WARN SET button of Defi-Link Control Unit II or
the SELECT button of Defi-Link control Unit is pressed, the meter
available for setting will change in the Warning Setup Mode.
 The
value of the setting is adjusted by pressing the UP button or DOWN
button of Defi-Link Control Unit II or Defi-Link Control Unit.
*The resolution of the UP button or DOWN button is adjusted to the
analog meter. Because of the difference in step values, the Display
value changes differently in each meter.
Pressing and holding the button will accelerate the adjustment rate
for easier use.
|
| Gauge
Mode |
This screen displays actual vehicle data and speed data for
meters connected to Defi-Link Control Unit II or Defi-Link control
Unit.
*Does not display Turbo Meter data or Tachometer data. |
| O.TEMP |
Oil Temperature Meter |
| OIL P. |
Oil Pressure Meter |
| EXT. T. |
Exhaust Temperature Meter |
| W. TEMP |
Water Temperature Meter |
| FUEL P. |
Fuel Pressure Meter |
Press ENTER to select and adjust the displayed meter.
 With
the ignition on, a "O" will be displayed for meters with
connected sensors. A"/" will be displayed for meters without
connected sensors, and selection/adjustment will be unavailabe. |
| 1. Single Gauge Mode
|
Each time the MODE SELECT button is pressed, the
displayed meter will change. Press ENTER to set the meter for
display.
|
|
|
|
| 2. Dual Gauge Mode |
Each time the MODE SELECT button is pressed, the
displayed meter will change. The upper display is set first,
then the lower display. Press ENTER to set the meter for display.
*For O. TEMP, W. TEMP, and EXT T. warnings, if the set warning
valoue is exceeded for the displayed meter, the Warning LED
will light and the corresponding display value will have reverse
lighting.
For OIL P. and FUEL P. warnings, if actual value drops below
the set waring value, the Warning LED will light and the corresponding
display value will have reverse lighting.
*The upper display has priority when REC, PLAY or PEAK is displayed.
|
|
|
|
| Speed
Mode |
|
This screen displays the vehicle speed.
|
|
Pressing the MODE SELECT button while in Gauge
Mode will bring up the Speed Mode. Along with display of current
vehicle speed, the maximum speed is always monitored and recoreded.
|
 |
|
| Triple
Warning Mode |
| This screen displays a warning when the Tachometer exceeds
the engine RPM set warning value. |
|
Pressing the MODE SELECT button while in Speed
Mode will bring up the Triple Warning Mode when the RPM signal wire
is connected to Defi-Link Control Unit II or Defi-Link Control Unit.
* This mode is not available when connected to Defi-Link Meter BF. |
|
|
 CLOSE |
