|
FACTORY SETTING VALUES
|
The After Idle Timer kit is set at the factory in the
AUTO MODE "S."
|
ITEM
|
DISPLAY
|
FACTORY SETTING
|
|
Timer Setting
|
C-
|
C-0
|
|
|
MODE SELECTION
|
Press the 
switch to change the setting modes as follows.
 |
|
SETTING THE DISPLAY MODE
|
1. Press the
switch until "A - 0" blink on the digital display. ( Set
values are displayed after mode settings.)
2. Press the 
switch to change the values and to change the display mode. Refer
to the table below.
|
Display
|
Mode
|
Details
|
|
A - 0
|
Real Mode
|
The current intake manifold pressure
is displayed as an LED bar and on the digital display as a numerical
value. A turbo mark on the display lights up in this mode. |
|
A - 1
|
Peak Hold Mode
|
The LED bar indicator provides an
analog display of the current intake manifold pressure. The
digital LED displays the maximum pressure recorded after the
vehicle ignition is turned ON. A turbo mark on the display goes
out in this mode. |
| A - 2 |
Timer Mode |
The LED bar indicator provides an analog
display of the current intake manifold pressure. The digital
LED displays the current value of the timer. A clock mark on
the display lights up in this mode. |
3. Press the
switch to finish setting the display modes.
NOTE: The display mode " A -2 " is not available if the
After Idle Timer is not connected.
|
|
|
SETTING THE TIMER MODE
|
*Press the
switch three times to change the timer setting mode.
(This mode is not available if the After Idle Timer is not connected.)
|
|
HOW TO USE THE AUTO MODE
|
1. Turn the ignition key ON.
2. With the unit operating in Auto Mode, the built-in micro
computer automatically sets the after idling time taking into
account the period of time during which the engine has been
running, the intake manifold pressure and other factors. The
factory setting of the after idling time is Auto Mode S.
3. When the ignition key is turned off, the after idling timer
begins to count down from a preset after idling time period.
4. The display on the after idle timer count down in one second
increments, and the engine turns off when the count reaches
"0." |
 |
|
|
AUTO MODE LEVELS
|
*In auto mode, it is possible to change the Length
of time over which the after idle timer counts down. In auto
mode the driver can set the interval to short(S), medium(M)
or long(L).
* The medium (M) interval is the default setting.
* To increase the after idling time, please set the mode to
L.
*To decrease the after idling time, set the mode to S. |
 |
|
|
HOW TO CHANGE THE LENGTH
OF THE AFTER IDLE TIME PERIOD
IN AUTO MODE
|
1. Turn the ignition ON. (Factory setting of Auto Mode is
S.)
2. Press the
switch three times until the display blinks "C - 0."(
A portion of " 0 " of " C - 0 " on the display
blinks.)
3. Press the
switch to set the desired after idle time period.
4. Press the switch
after setting the after idle time period. |
 |
|
|
HOW TO USE THE MANUAL
MODE
|
The maximum time interval for the After Idle Timer is 9 minutes
50 seconds.
1. Turn the ignition ON.
2. Press the
switch three times until "C - 0" blinks on the digital
display.
3. Press the
switch to set "C-3".
4. Press the
switch to set the normal display.
5. Press the
switch three times until "C - 3" blinks on the digital
display.
6. Press the 
switch to change the number of Minutes on the display.
7. Set a desired value by pressing the
and  switches. |
 |
8. Each time the
or switch
is pressed, the value on the display is increased or decreased
by one minute (0 to 9 minutes).
9. Press the
switch until the Seconds display blinks.
10. Set a desired value by pressing the
and switches.
11. Each time the UP or DOWN switch is pressed, the value on
the display is increased or decreased by ten seconds (00 to
50 seconds).
12. Press the MODE/PWR switch to finish the manual mode setting. |
|
|
HOW TO CANCEL THE TIMER
FUNCTION
|
When you would like to suspend operation
of the after idling timer, you can cancel the timer function as follows:
1. Set the after idle timer in the manual mode and set the timer to
"0.00." No after idling occurs.
2. If you want to suspend the operation of the after idle timer immediately,
press the
switch and hold it for more than 2 seconds during after idling. The
display reads "0.00" and the engine will turn off. ( Setting
value itself is not reset.)
|
Please note that Section 25269 of the California Vehicle Code
provides that " no person shall display a steady burning
red warning light on a vehicle," except as may otherwise
be provided herein. The exceptions permitting red lights apply
to emergency vehicles and other situations that are not be applicable
to the V.S.D. instruments. Other states have similar prohibitions
in their respective vehicle codes.
Note that the V.S.D. display unit projects light upwards upon
the transparent screen, so that the image can be reflected into
the driver's line of sight. In some situations, it is possible
that the light from the LEDs of the display unit may be visible
to a person located in front of the vehicle, either because
the angle at which the display unit is mounted on the dashboard
or because the angle of the dashboard is inclined towards the
front of the vehicle.
If this is the case, the applicable regulatory authorities might
interpret the use of the V.S.D. display unit to be a violation
of California Vehicle Code Section 25269 or other state vehicle
codes. |
|
End
of Life Products |
